|
|
|
240-260-280Z Suspension |
|||
| Camber Plate Kits Each kit contains (2) mounting plates, (2) sliders with 5/8 spherical bearings, (2) spring perches, (1) needle bearing kit and mounting hardware. The kits are made from black anodized aluminum. To use the spherical bearing, it may be necessary for you to turn down the shock shaft where it goes through the bearing in the slider. Please specify what shock you are using when ordering. | |||
| Photo | Part # |
Description | Price |
 |
204-1003 |
Camber Plate Kit, Datsun 240/260/280Z centered slots, bolt-in installation |
275.00 |
 |
204-1017 | Camber Plate Kit, Datsun 240/260/280Z Street Prepared, biscuit type |
185.00 |
 |
201-1625 | Camber Plate Spherical Bearing, 5/8" Dia |
25.00 |
|
|
201-1750 | Camber Plate Spherical Bearing, 3/4" Dia |
25.00 |
|
Threaded Collars We supply two types of threaded collars. One is machined aluminum and the other is nickel plated steel. The aluminum collars are 5" long by 2 1/8" ID and have two jam nuts which allow you to raise or lower the car. The collars are designed for a 2.5" ID coil-over spring. The collars are supplied with weld rings. The IT collar has one bottom weld ring and the standard collar has both top and bottom weld rings which holds the collar in place. The steel threaded collars do not require weld rings. |
|||
 |
214-1100 | Adjustable Threaded Collar, 2" dia. strut tube, 2.5" ID spring, alum. with steel rings pressed into ends for welding to strut, 5" Long |
130.00 |
 |
214-1101 | IT Legal Adjustable Spring Spacer, 2" Dia. Strut Tube, 2.5ID |
120.00 |
 |
214-1225 |
Steel Nickel Plated Threaded Collars - Steel threaded collar, nickel plated, 2 1/4" O.D. x 6" long. Fits 510, 240/26-Z or any 2"O.D. strut tube. |
$120.00 |
 |
210-1112 | 8" Steel Threaded Collar with jam nuts |
130.00 |
 |
224-1003 | Front Control Arm Bushing Kit This kit consists of steel bushings and sleeves that replace the old rubber bushings. Spherical bearing type for 5/8" bolt. | $150.00 |
|
|
224-1002 | Front Control Arm Bushing Kit This kit consists of steel bushings and sleeves that replace the old rubber bushings. Spherical bearing type for stock bolt. |
$150.00
|
 |
224-1201 |
Knuckle Risers These 1" aluminum spacers are used to correct the suspension geometry changes (bumpsteer) that occur in severely lowered cars for both street and race. The mount between the steering arm and the bottom of the strut. They do NOT raise the ride height. Bolts are included. pr. |
$80.00 |
 |
234-1003 | Front Diff Solid Mount Kit |
$45.00 |
 |
234-1002 | Rear Diff Solid Mount Kit |
$40.00 |
 |
224-1212 |
Steering Side Rod Ends These are adjustable tubular rods are intended to replace the stock tie rod ends. They have 5/8" Teflon lined rod ends. Incl. hardware. | $215.00 |
 |
299-1240 | Labor to reinforce and install rod-end to rear control arm. Per end. | $300.00 |
 |
284-1240 | Adjustable Racing Front Stabilizer Bar 11/8" tubular | $395.00 |
 |
284-2245 | Adjustable Racing Rear Stabilizer Bar 5/8" solid | $395.00 |
 |
299-1011 | Labor to install swaybar mount on rear control arm | $65.00 |
|
|
|
SHOCKS
Tokico 5 way- adjustable Illumina shock series was
engineered specifically as a tuning device for the enthusiast who
requires the best in performance for the street/track and ride comfort
for real-world driving. Tokico Ilumnia - set of four Tokico's HP Series (auto-adjust) minimizes low speed damping force and greatly increasing damping at medium and high piston speeds for improved compliance, tire adhesion, and handling. Tokico HP - set of four |
CALL
CALL |
|
THERE WILL BE A 20% RESTOCKING FEE
FOR ALL APPROVED RETURNS. THERE IS NO STATED OR IMPLIED
WARRANTY DUE TO THE UNUSUAL STRESSES PLACED ON RACING/HIGH
PERFORMANCE STREET PARTS AND BECAUSE WE HAVE NO CONTROL OVER
HOW THEY ARE USED. PRICES ARE SUBJECT TO CHANGE WITHOUT
NOTICE.
|